 Rank: Junior Member Groups: Registered
Joined: 9/18/2006(UTC)
Posts: 10
|
"I have just switched to a digital thermometer. I am using an extractor pro series with the size 13 1/2 rubber cork at the top of the column. Does anyone know it I have to find a solid stopper and drill it myself or does someone have one? The reason I ask is the hole in the stopper is to big for the probe.
Thanks Jim"
|
|
|
|
|
|
 Rank: Administration Groups: Administrators
Joined: 2/10/2002(UTC)
Posts: 501
Was thanked: 8 time(s) in 8 post(s)
|
Actually, we offer the bungs drilled or without a hole (same price) on our website.
|
|
|
|
|
|
Rank: Junior Member Groups: Registered
Joined: 9/18/2006(UTC)
Posts: 10
|
"Rick:
Thanks for the information. I am going to be placing an order shortly.
Thanks Jim"
|
|
|
|
|
|
Rank: Junior Member Groups: Registered
Joined: 3/16/2007(UTC)
Posts: 52
|
"I was faced with the same issue when I changed over to a digital thermometer. This was my approach... I drilled a 1/8" hole next to the center hole (the rubber doesn"t drill well...but just keep pushing the bit in and out...you"ll never get a clean bored hole).  I then went to a 3/32" bit because it was too hard to get the probe in and out. Ok...That part works. Now for the hole in the middle. Getting the stopper out after a run is a little tough as there is no handle to grab hold of. I used a 1/4 X 3" stainless steel bolt, two nuts and 2 washers to solve the problem. Thread one nut on the bolt (run it almost to the head of the bolt), add 1 washer and insert the bolt through the bung from the top. Now on the bottom add the other washer and nut (I applied a couple of wraps of Teflon tape on the end of the bolt...more for a thread-lock than a sealant). Thread the nut so that there is only a thread or two of the bolt extending through the nut. Now tighten the top nut down on the bung...not too tight! Now I have a short length of the bolt and the bolt head (sticking out the top of the bung) that I can use for a handle to remove the bung from the tower when I"m finished with a run. This has worked real well for me, quick and easy. Travis :)"
|
|
|
|
|
|
 Rank: Newbie Groups: Registered
Joined: 8/26/2007(UTC)
Posts: 3
|
"A few years back I built a thermometer setup for smoking meat (Big Green Egg); it has two type K thermocouples (high temp sensors) and used a radio to talk to a remote unit connected to a computer. I wrote some software for the computer end of things that included timers, temp alarms, network connectivity, etc. If anybody is interested I can point you at more info and dig out the specs, part numbers, software (Windows), etc. Its very much a work in progress but was a fun introduction to electronics/hardware. Sorry to the purists but automating and device connectivity are kind of 'my thing'.  "
|
|
|
|
|
|
Rank: Junior Member Groups: Registered
Joined: 3/16/2007(UTC)
Posts: 52
|
"Greg,
Yes, I would be interested in knowing more about what you did! We always have the laptop outside when we are running Tin Man. I track everything on an Excel spreadsheet. Being able to have all the data upload and track it from the computer sounds good to me. Thanks!
Travis:)"
|
|
|
|
|
|
Rank: Newbie Groups: Registered
Joined: 8/26/2007(UTC)
Posts: 3
|
Ya sure ya betcha! I'll PM you.
Since both components have RS232 output (serial port) you don't really need to include the radio components - if you are willing to leave the laptop outside.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
